Tokin Metal-Sealed Actuators
ASL170C801 - High Temperature (up to 150°C)
|
Without Flange
|
ASL170C801WP-A0LF - Plane TopASL170C801WD-A0LF - V-Groove TopL = 24.4±0.5 1-9 units: $685.00 10-24 units: $665.00 25-50 units: $640.00 >50 units: Request a quote |
|
Female Thread
|
ASL170C801NP0LF - Plane TopASL170C801ND0LF - V-Groove TopL = 38.4±0.5 1-9 units: $715.00 10-24 units: $695.00 25-50 units: $670.00 >50 units: Request a quote |
|
Flange
|
ASL170C801FP0LF - Plane TopASL170C801FD0LF - V-Groove TopL = 32.4±0.5 1-9 units: $715.00 10-24 units: $695.00 25-50 units: $670.00 >50 units: Request a quote |
|
|
P - Plane TopD - V-Groove Top |
Specifications
| Item |
Standard | Conditions |
|
Operating temp range |
-40 to +150°C |
When applied with a DC voltage:
Ambient temp
When driven by an AC voltage:
Ambient temp + Temp rise
due to generated heat
|
|
Rec Storage cond |
-5 to +40°C | |
| Max driving volt | 150V DC | |
| Displacement |
19.0 ± 3 um | At 150V DC |
| Blocking force |
800 N |
Force required for restricting
the displacement to 0 when the
maximum driving voltage is applied.
|
| Capacitance |
1.34 uF ± 20% | f = 1kHz; V=1Vrms |
| Dissipation Factor |
5.0% or less | f = 1kHz; V=1Vrms |
| Insul Resist |
30 MOhm | Value obtained in 1 minute at 150V DC |
| Resonant Freq | 14 kHz |
With both ends of the
actuator in free state. Typical value
of the element under test conditions
|
| Airtightness | 1x10-8 atm cc/sec or less | |
|
Temp Cycle Test |
Displacement: Initial value ± 30%
Capacitance: Initial value ± 30%
Tan Delta: Less than initial rated value
Insulation resistance: 1MOhm or more
Apperance: No noticeable defect
|
Room temperature (3 min)
-40°C (30 min)
Room temperature (3 min)
+150°C (30 min)
Rep of 10 cycles of the above
|
|
High Temp Shelf Test |
Displacement: Initial value ± 30%
Capacitance: Initial value ± 30%
Tan Delta: Less than initial rated value
Insulation resistance: 1MOhm or more
Apperance: No noticeable defect
|
Temperature 150°C ± 2°C
Time 1,000 ± 48h |
|
Solvent resist Test |
Displacement: Initial value ± 30%
Capacitance: Initial value ± 30%
Tan Delta: Less than initial rated value
Insulation resistance: 1MOhm or more
Apperance: No noticeable defect
Mark: Easily legible
|
Solvent: Isopropyl alcohol
Temperature:23 ± 5°C
Time: Immersion for 1 min
|
|
Heat resist Test |
Displacement: Initial value ± 30%
Capacitance: Initial value ± 30%
Tan Delta: Less than initial rated value
Insulation resistance: 1MOhm or more
Apperance: No noticeable defect
Mark: Easily legible
|
Temperature: 150 ± 3°C
Time: 96 ± 4h
|
Dimensions for Mounting Options
 |
 |
 |
 |
