Piezoelectric Tube Scanners
Piezoelectric Tube Scanners
Piezoelectric tube scanners are thin cylinders of radially poled piezoelectric material with four external electrodes and a solid or quadrant internal electrode. When a voltage is applied to one of the external electrodes, the actuator wall expands which causes a vertical contraction and a large lateral deflection of the tube tip. A circumferential electrode can be used for vertical or radial extension and contraction.
Piezoelectric tube scanners are used extensively in scanning probe microscopes and applications such as fibre stretching and beam scanning.
|Order Code||Length||Diameter||Thick.||Max Volt.||Scan Range||Extension Range||Quadrant Cap.|
When the base of the tube is fixed, the tip translations delta-x and delta-y are approximately
where delta-x and delta-y are the x and y axis deflection, d31 is the piezoelectric strain constant, L is the length of the tube, D is the outside diameter, h is the tube thickness, and Vx and Vy are the driving voltages which are applied oppositely to either side of the tube. The tube deflects towards the electrode with the positive voltage.
The vertical contraction due to a voltage applied to all four quadrants is approximately
This is also the vertical contraction when a negative voltage is applied to the internal electrode. The diameter expansion due to a voltage applied on all four quadrants or a negative voltage applied to the internal electrode is approximately
The expansion range in the vertical and radial directions can be doubled by driving the internal and external electrodes with opposite voltages.
Driving Piezoelectric Tubes with the TD250 Amplifier
The TD250 is an ultra-low noise, six-channel 250V amplifier optimized for driving piezoelectric tube scanners. Although many configurations are possible, the driven internal electrode configuration shown below is simple and provides the maximum X, Y and Z travel range.
Driving piezoelectric tubes with the TD250
In the driven internal electrode configuration, the X and Y electrodes are driven in the standard way with equal and opposite voltages. By applying the full-scale negative voltage to the internal electrode, a contraction equal to half the vertical scan range is obtained. This method exploits the higher positive electric field strength of the piezoelectric material, which is usually five times the negative electric field strength. Care must be taken not to apply positive voltages to the internal electrode since this can lead to depolarization.
Driving Piezoelectric Tubes with PDm200B Modules
The PDm200B can be configured in the ±200V range to drive piezoelectric tubes. The connection diagram for a typical positioning application is illustrated below. Two amplifiers are required for the x and y axis. The centre electrode can be grounded or driven if vertical deflection is required.
Driving piezoelectric tubes with the PDm200B
The most common mounting configuration is the cantilever arrangement with a fixed base and free end. The base can be bonded directly to an insulating surface with a two part epoxy such as Araldite, or a high viscosity Cyanoacrylate such as Loctite Super Glue Gel. Piezoelectric Tubes can also be bonded to a conductive surface by removing a small amount of electrode as described in "Electrodes" below.
The tubes are supplied with a Nickel electrode. The internal electrode is continuous and the external electrodes are quartered. Electrode area can be removed by etching with dilute Nitric Acid. Custom electrode configurations are available on request.
In applications that require high magnetic fields, the Nickel electrodes can be replaced with Copper or Gold. Copper is an economical choice but Gold provides excellent corrosion resistance and electrical conductivity.
Electrical Current Requirements
The required current is I=C dV/dt where I is the current, C is the effective capacitance, and dV/dt is the voltage rate of change. For a sine-wave, the required peak current is equal to: Ip=2(pi)fVp-p where Vp-p is the peak-to-peak voltage. For a triangle wave, the required peak current is equal to: Ip=2CfVp-p
Wires can be attached using conductive epoxy (Circuitworks CW2400) or standard solder and Rosin flux. After flux application, a one second contact with a 300C iron is recommended.
Piezoelectric tubes do not contain any outgassing materials and are fully vacuum compatible.
The material PZT-5H works well at cryogenic temperatures. As a guide, the sensitivity reduces by a factor of four. However, at cryogenic temperatures the applied voltage can be increased to +/-2 kV/mm, which can regain or exceed the room temperature deflection but requires a high voltage.
For example, the predicted deflection of the TB6309 tube is +/-10 um with an applied voltage of +/-250 V. However, the full +/-40 um range can be recovered by increasing the voltage to +/-1 kV.
- Custom dimensions and thickness
- Custom electrode configurations
- Custom wiring arrangements / connectors
- Mounting platform design and fabrication
The piezoelectric material is similar to PZT-5H and Navy Type VI.
|Dielectric constant||e33/e0||3500||@1 kHz|
|Dissipation fator||tan δ||2.5||% @1 kHz|